Wiring & Hardware

Settings you normally make once, when wiring the cabinet: how the board's mode pins behave, what spare pins do, kiosk lock-down, input debounce and the USB identity.

The top of the Wiring and Hardware page: the five Mode input wiring groups and the folded Switch and jumper wiring guide
The top of the Wiring & Hardware page: the Mode input wiring groups (here the player layout pins are DISABLED), then the folded Switch & jumper wiring guide.

This page is in the Controller group of the sidebar. Everything on it is stored on the board, so the controller must be plugged in to see and change it. Nothing reaches the board until you press Save to controller at the bottom, except the USB identity, which has its own button.

Mode input wiring

This section controls the board's dedicated mode pins: the header pins for mode buttons, switches and jumpers. All of them are optional. DEFAULT (or DEFAULT / AUTO) works the way the printed manual describes, with detection jumpers read at power-on. If you pick any other type here, no detection jumpers are needed at all, because the app setting replaces them. Any setting that stops using a pin frees that pin, so you can use it under Spare pins as player buttons further down this page.

Each group of mode pins has its own row. The note under each row explains what the current choice does.

GroupChoicesWhat the choices mean
Stick mode inputs (DPAD / ANA-S / ANA-F) DEFAULT / AUTO · SWITCH · BUTTONS · DISABLED Auto: a grounded DPAD pin at power-on means the stick modes are wired as switches. SWITCH: the pins are treated as switches, and the DPAD detection ground is no longer needed. BUTTONS: the pins are treated as buttons. DISABLED: all three pins are ignored and freed.
Player layout inputs (2P / 4P / TS) DEFAULT · DISABLED Default: the pins work as jumpers, switches or buttons, as in the manual. DISABLED: 2P, 4P and TS are ignored and freed.
Disconnect input (DIS) DEFAULT · TOGGLE · DISABLED Default: grounding DIS enters keyboard mode (as in the manual), which also powers the DongleMaster. TOGGLE: each press of DIS switches keyboard mode in and out, with no hold needed. The other mode inputs then keep working inside keyboard mode instead of exiting it. DISABLED: DIS is ignored and freed.
Turbo inputs (TURBO / !TURB) DEFAULT / AUTO · SWITCH · TWO BUTTONS · ONE BUTTON · DISABLED Auto: see the wiring note below. SWITCH: a switch wired to !TURB, with TURBO freed and no detection ground needed. TWO BUTTONS: TURBO turns turbo on and !TURB turns it off. ONE BUTTON: a single button on TURBO toggles turbo, and !TURB is freed. DISABLED: both pins are ignored and freed. The long-hold shortcuts still work.
8-to-6 inputs (8TO6 / !8TO6) DEFAULT · SWITCH · TOGGLE · DISABLED Default: 8TO6 turns the mode on (button, switch or jumper) and !8TO6 turns it off. SWITCH: a switch on 8TO6 (closed = on, open = off), with !8TO6 freed. TOGGLE: one button on 8TO6 toggles the mode, with !8TO6 freed. DISABLED: both pins are ignored and freed.

Turbo in Auto: for a turbo switch, permanently ground the TURBO pin (that ground is the detection jumper) and wire the switch itself between !TURB and GND. Grounding !TURB at power-on instead gives one-button turbo (button on TURBO). If you ground neither, you get two buttons (TURBO turns turbo on, !TURB turns it off).

For turbo switch wiring, follow the Utility's own wiring guide (below and on screen). The turbo-switch wiring drawn in some printed manuals is the wrong way round.

If your board doesn't have the pins for a group, that group stays visible but greyed out, with a note saying so. Those modes still work from the app, shortcuts and scripts, and Buttons that trigger modes and pinball inputs on Default XInput Mapping can put them on any player button. While kiosk lock-down is on, it overrides all of these groups.

Switch & jumper wiring guide

Click Switch & jumper wiring guide under the groups to open this table:

FunctionWiring
Slow-analog switchGround the DPAD pin, then wire the switch to ANA-S
Fast-analog switchGround the DPAD pin, then wire the switch to ANA-F
4-player switchGround the 2P pin, then wire the switch to 4P
Twinstick switchGround the 2P pin, then wire the switch to TS
Disconnect switchGround the 2P pin, then wire the switch to DIS
Turbo switchGround the TURBO pin, then wire the switch to !TURB (or set Turbo inputs to SWITCH and skip the TURBO ground)
8-to-6 switchGround the !8TO6 pin, then wire the switch to 8TO6
InterlockJumper the INT pin to ground (or force it with the Interlock setting on the Modes page)

3-position switches: for stick modes, ground ANA-F and wire DPAD / ANA-S to the outer positions. For player modes, ground 2P and wire 4P / TS to the outer positions.

The grounds also decide which mode a switch's OFF position selects. Keep them even when you choose SWITCH in the app; only their power-on detection role becomes optional.

To check your wiring, open Test & Log: Mode & special pins shows each pin's raw state as you flip a switch or press a button.

Spare pins as player buttons

The Spare pins as player buttons table: free pins are Available, pins still used by their mode are greyed out with a note on how to free them
The spare-pins table. 4 PLAYER is ticked (the player layout pins were disabled above); the stick-mode, turbo, 8-to-6, interlock and disconnect pins are still in use, so they are greyed out with a note saying how to free them.

Your board has dedicated mode inputs: player-layout pins, stick-mode pins, TURBO, 8TO6, INT, DIS and, on some boards, right-stick and pinball pins (like the 2000H's). If you don't use one for its mode, this table turns it into an extra player control and, in keyboard mode, its own key. For example, a spare pin can become a player's LT. The table only lists pins your board actually has. While a pin is ticked here, its own mode function is off.

ColumnMeaning
OnTick to use this pin as a player control.
Special inputThe board pin, for example TURBO ON, 8to6 OFF, RIGHT-STICK, Nudge Left or PINBALL A.
Acts as player inputTwo drop-downs. The first picks whose control it becomes (a cabinet position or a fixed player). The second picks which control: a direction, a button, LT or RT.
Types key (keyboard mode)The key it types while the board is in keyboard mode. Leave it on (target input's key) to type whatever key the player input it acts as types on Default Keyboard Mapping.
StatusWhether the pin is free to use (see below).

Status: which pins are free

StatusMeaning
AvailableThe pin is free. Tick On and choose what it acts as.
In use — free it: …Its mode still needs it, so the row is greyed out and can't be ticked. The note says which setting frees it (see the list below).
Remap overrides the mode functionThe pin is ticked here but its mode setting still uses it. The mapping wins.

How to free each pin:

PinsFreed when
2 PLAYER, 4 PLAYER, TWINSTICKPlayer layout inputs are DISABLED
D-PAD, ANALOG FAST, ANALOG SLOWStick mode inputs are DISABLED
TURBO ONTurbo inputs are SWITCH or DISABLED
TURBO OFFTurbo inputs are ONE BUTTON or DISABLED
8to6 ON8-to-6 inputs are DISABLED
8to6 OFF8-to-6 inputs are SWITCH, TOGGLE or DISABLED
INTERLOCK (toggle)Interlock mode is On or Off (Modes page)
DISCONNECT / KEYBOARDDisconnect input is DISABLED
RIGHT-STICK and the pinball pinsAlways available

While kiosk lock-down is on, it frees every mode pin it locks. The INT pin still follows the interlock setting, and in LOCKED XINPUT/KEYBOARD (DongleMaster Support) the DIS pin stays the keyboard switch.

Positions and players

The first Acts as player input drop-down lists the physical stick positions on the cabinet: Far-Left, Mid-Left, Mid-Right and Far-Right on 4-player boards (Left, Middle, Right on 3-player boards; Left, Right on 2-player boards), then Player N - Fixed. A position keeps working when 2-player or 4-player mode reorders the players. Player N - Fixed follows the Xbox player number after reordering instead.

Example: give a spare pin its own key

Set the group that owns the pin to DISABLED above, for example Turbo inputs. Then tick On for that pin in this table, pick a player input for it, choose a key such as P (pause in MAME) under Types key, and click Save to controller.

Board behaviour

Kiosk/Lockdown Mode

Kiosk mode locks the cabinet into its power-on defaults for public use. The board's own mode buttons, switches and shortcuts stop working. Mode changes from this app, its control scripts (LaunchBox / RetroFE) and PC hotkeys still work. Interlock keeps its own setting, and spare pins keep working.

ChoiceWhat happens
OFF (ALL MODES)Normal operation: all modes available.
LOCKED XINPUTLocked to XInput with the power-on defaults. There's no mode switching from the board, and every mode pin is freed.
LOCKED DISC./KEYBOARDLocked to keyboard mode (the board boots straight into it). There's no mode switching from the board, and every mode pin is freed.
LOCKED XINPUT/KEYBOARD (DongleMaster Support)Everything is locked except the DIS input. Pressing it switches between XInput (arcade controls) and keyboard mode, and keyboard mode also powers the DongleMaster so wireless gamepads become the main controls. All other mode pins are freed.

While kiosk mode is on, the Mode input wiring groups above are locked. On a 4000H2 whose DIP1 (kiosk lock-down) switch is on, the note under the buttons says the lock is held on by that switch and can't be cleared from the app.

Input debounce

Debounce is how long an input must stay in its new state before the board believes it. This setting only appears when your board's firmware supports it.

FieldShipped value
Joystick directions1.5 ms
Action buttons1.5 ms
Start/Back & mode inputs10 ms

Values go from 0.1 to 25.5 ms in steps of 0.1 ms. The board checks its inputs about every 0.4 ms, so differences smaller than that can't be measured. Lower values respond faster, but a worn or bouncy switch may register twice. Higher values are safer but add lag.

The shipped values suit every microswitch Pacto Tech has tested. Only change them if a specific control double-fires or feels sluggish.

USB identity (Windows / Linux / DirectInput mode)

This controls how the board introduces itself over USB, so set it to match the machine the board lives in. The setting only appears when your board's firmware supports it.

ChoiceUse it for
WINDOWS (XINPUT)The standard Pacto identity (XInput pads), with full Utility support on Windows. This is the default.
LINUXLinux systems. The board presents the stock Xbox 360 controller identity, so the system's own built-in driver runs the pads. Batocera, RetroPie, Lakka, Knulli, ROCKNIX, MiSTer and the Steam Deck are all Linux systems, even when they don't look like it.
DIRECTINPUT (HID GAMEPADS)Games and front ends that only accept DirectInput pads (older PC games, some MAME setups). Each player becomes a generic HID game controller. The Utility stays connected, but XInput-only games won't see the controls.

Picking a choice doesn't change anything yet. Click Apply identity (saves & restarts the board) and confirm: the board saves the setting and restarts with the new identity. This button has its own save and is not part of Save to controller. The line under the choices says which identity is active.

Linux mode on a Windows PC: Windows' Xbox driver takes over the whole board, so the Utility can only reach it in keyboard mode. To change the setting back, flip the DISS. input (keyboard mode), change the setting here, then flip it back.
So far, Linux mode has been tested with Linux running in virtual machines.

Saving and restoring

The whole Wiring and Hardware page: mode input wiring, the spare-pins table, Board behaviour with kiosk, debounce and USB identity, and the save buttons
The whole page on a 4-player board: Mode input wiring, Spare pins as player buttons, Board behaviour (kiosk, debounce, USB identity with its own Apply button), then Save to controller and Restore Wiring Defaults.
Back up settings to file (on App Settings) includes the spare-pins table, but not the Mode input wiring, kiosk, debounce or USB identity. Note those down if you want to set up another board the same way.
← Previous: Pinball InputsNext: Overlays →