Pacto Tech — Release Notes

Updates for the Pacto Tech Utility app and controller firmware.

20261115_0452 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-11-14

Front ends no longer go black when a game closes while the Utility's window is open.

With the PactoTech Utility's window left open behind a front end (reported with Attract-Mode Plus), closing a game could leave a black screen: Windows handed the screen to the Utility instead of the front end, and the front end could not take it back. The Utility now minimizes its window whenever a front end or game fills the screen it is on, so a closing game always returns to the front end. Its window stays on the taskbar, and you can open it again from the tray as usual.

Also: the app now says "PactoTech" (one word) everywhere you see it.

Firmware is unchanged from the previous release; there is no need to update your board. F103VB boards: use the one-click ST-Link update.

20261115_0452 stable App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-11-14

Front ends no longer go black when a game closes while the Utility's window is open.

With the PactoTech Utility's window left open behind a front end (reported with Attract-Mode Plus), closing a game could leave a black screen: Windows handed the screen to the Utility instead of the front end, and the front end could not take it back. The Utility now minimizes its window whenever a front end or game fills the screen it is on, so a closing game always returns to the front end. Its window stays on the taskbar, and you can open it again from the tray as usual.

Also: the app now says "PactoTech" (one word) everywhere you see it.

Firmware is unchanged from the previous Stable release; there is no need to update your board. F103VB boards: use the one-click ST-Link update.

20261106_0419 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-11-05

Firmware updates over USB work reliably again.

Updates could fail with "the bootloader did not answer" or "did not accept the claim", and the board went back to its old firmware unharmed. This Utility now updates boards that had the problem, and every firmware image in this release includes a corrected bootloader for boards flashed with an ST-Link.

If your board is on a recent firmware, update the Utility first, then update the firmware from Update / About. Your settings are kept.

Boards on Legacy Gen 1 firmware, or any board you want the corrected bootloader on: use Update / About > Advanced update options to flash with an ST-Link. A USB update can't replace the bootloader, but the updated Utility handles that for you.

New installs now start on the Stable channel. If you chose a channel yourself, it stays as you set it.

All boards' firmware is rebuilt in this release; apart from the corrected bootloader in the ST-Link images, nothing changes on the 1000T, 2000T, 3000T or 4000T since the previous release. F103VB boards: use the one-click ST-Link update.

20261106_0419 stable App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-11-12

First Stable release: the Pacto Tech Utility and 2nd generation firmware.

This is the first release on the Stable channel, which is the channel new installs use. It is the same build as 20261106_0419.

Pacto Tech Utility for Windows: - Game profiles set the board up for each game and put it back when the game closes. - On-screen banners show every mode change. - Remap buttons and keyboard keys, for every player or one position. - The Control Test checks every control and the player order Windows gave them. - A kiosk lock stops mode changes from the panel. - Settings for ATLAS0 and ATLAS1 trackball boards.

2nd generation firmware supports previous hardware, so boards bought before November 2026 can run it too. Updates are optional: if your cabinet works the way you like, you can leave it as it is.

Updating: - Boards already on 2nd generation firmware update over the USB cable from Update / About. Your settings are kept. - Boards on Legacy Gen 1 firmware need one ST-Link flash first, from Update / About. The Utility does the flash for you. After that, updates arrive over USB. - Automatic updates for the app and the firmware are an option. They are off by default for stability.

F103VB boards: use the one-click ST-Link update.

20261106_0327 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-11-05

1000T fixes: game profiles no longer stop the 1000T's controller, and the SpecVision screen shows the 1000T's real layout.

1000T firmware: - A game profile set to Twin-Stick (or 4 Player) could stop the 1000T's controller responding until it was unplugged, and a 4 Player layout stopped the second stick. The 1000T now treats any such layout as its Normal layout (first stick = left analog stick, second stick = right analog stick). - SpecVision OLED status screen: the 1000T showed "4 PLAYER (1234)" as its layout. It now shows NORMAL or RIGHT STICK, and switching to Right-Stick mode shows its own screen.

Utility: - Game profiles no longer send a player layout to a 1000T, so 1000Ts that haven't updated their firmware yet are protected too. Stick output, 8-to-6, interlock, turbo and the other profile settings still apply. - Install Legacy Gen 1 firmware: an error message still said "2025 firmware"; it now says Legacy Gen 1.

The 1000T user manual is corrected: Normal is the power-on layout and Right-Stick mode swaps the two sticks, the DISC input switches to Disconnect / Keyboard mode, and the optional SpecVision screen works on the 1000T.

3000T firmware: the SpecVision status screen now names the layout in 2 Player and Twin-Stick modes ("2 PLAYER (132)" / "TWINSTICK") instead of leaving it blank or wrong.

The 2000T, 4000T and other boards' firmware is unchanged from the previous release; there is no need to update them. F103VB boards: use the one-click ST-Link update.

20261102_0107 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-11-01

The 1000T's Kiosk/Lockdown setting now locks every panel shortcut, plus clearer wiring help and naming in the Utility.

1000T firmware: with Kiosk/Lockdown turned on, the SHIFT button shortcuts (SHIFT + BACK, START, A, LB, RB or X) and the Right-Stick input no longer change modes, so a locked 1000T stays exactly as you set it. The Utility can still change modes, and the "DISC only" lock still lets the DISC input switch to keyboard mode. Nothing changes when the lock is off.

Utility: - The firmware your boards shipped with before November 2026 is now called "Legacy Gen 1 firmware" everywhere. Update / About > Advanced update options > Install Legacy Gen 1 firmware with ST-Link puts it back, and the ATLAS Trackball page marks older ATLAS firmware "(Legacy Gen 1)". - Wiring & Hardware: the 3-position switch tip now matches the board - for the stick modes, ground DPAD and wire ANA-S / ANA-F to the outer positions. The keyboard-mode tip now says to use a momentary button between DISC and GND (each press switches). The input is called DISC, as printed on the boards. - Default Keyboard Mapping: the key tables are named by cabinet position (Far-Left, Mid-Left, Mid-Right, Far-Right), like the XInput mapping page, so it is clear which station types which keys. - ATLAS Trackball page: on an ATLAS1 (which has no DIP switches) the default choices now say what they do there - Off, Player 1, 100 % speed. - Test & Log: the Control Test's stick percentages are no longer cut off when a stick is pushed. - Update / About: the controller status no longer gets stuck on "Checking...". - Modes: the 1000T no longer lists a turbo shortcut it doesn't have.

The 2000T, 4000T and other boards' firmware is unchanged from the previous release; there is no need to update them. F103VB boards: use the one-click ST-Link update.

20261031_1444 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-10-31

New firmware for the ATLAS0 and ATLAS1 trackball boards, installable from the Utility, and the Utility now keeps a copy of each trackball's settings.

ATLAS firmware 20261031: the trackball and buttons respond much faster. The PC now reads the board every millisecond instead of every 10 ms, and the board no longer pauses for about 20 ms each time it sends a button press or movement, so fast spins, drags and quick taps arrive smoothly and on time. The trackball and buttons also keep working while the Utility or a terminal is talking to the board, and a program that opens the board's COM port without reading it can no longer freeze it.

Settings are now stored in a part of the chip's memory that every ATLAS board is guaranteed to have, so they save reliably on every board. Updating keeps all of a board's settings and button mappings, including its player number. Other fixes: a key or volume button held while you change its mapping or restore factory defaults no longer stays stuck on the PC; releasing one of two held media keys no longer releases the other; media keys such as Email, Calculator and the web keys can now be assigned; F13-F24 can be chosen by name; the right mouse button is named correctly in exported settings; and a bad or interrupted settings import no longer changes the wrong setting or leaves the board waiting.

To update an ATLAS board: plug it in, open the ATLAS Trackball page, click Read from board, then Update firmware with ST-Link. This needs an ST-Link connected to the board's SWD pins (SWDIO, SWCLK, GND) with the board plugged into USB; it takes about 10 seconds.

Settings copy: every time the Utility reads or saves an ATLAS board, it keeps a copy of that board's settings on the PC. If a board ever comes back on factory settings, the ATLAS Trackball page offers to put its saved settings back.

The controller firmware is unchanged from the previous release; there is no need to update it.

20261030_0355 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-10-29

ATLAS trackball settings in the Utility, and the original 2025 firmware built in.

New "ATLAS Trackball" page (under Controller): plug in an ATLAS0 or ATLAS1 trackball board with its USB cable and click Read from board to see every setting - axis reversal and swap, mouse speed, player number (USB ID) and button debounce - and what each button sends (mouse button, keyboard key, media key or nothing). Change anything and click Write to board; the board is read back to confirm. Restore factory defaults and Reboot board are there too. No terminal program is needed any more; close any serial terminal connected to the board first.

The original 2025 firmware for the 4000T, 4000H, 2000T (including its 8to6 right-hand version), 2000H and 1000T is now included in the Utility. Update / About > Advanced update options > Install 2025 firmware with ST-Link puts it back on a board. When a controller running the 2025 firmware is plugged in, the Utility now says so at the top and greys out the pages that need the current firmware, instead of reporting that no controller is connected.

The controller firmware is unchanged from the previous release; there is no need to update it.

20261027_0431 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-10-26

The in-game overlay no longer crashes games.

The Utility's in-game overlay (the mode banners drawn inside fullscreen games) could crash some games when it loaded: OpenGL games on NVIDIA graphics (RetroArch's OpenGL drivers, Dolphin, Flycast, MAME's OpenGL mode, yuzu and others), an occasional crash while it was starting up, and a crash inside NVIDIA's driver with RetroArch. These are fixed, and banners now also appear in PPSSPP's Direct3D 9 mode and MAME's bgfx renderer.

The overlay now waits until a game has been fullscreen for a few seconds before loading, and it is never loaded again into a game that closed unexpectedly right after it loaded (that game falls back to the other ways the Utility shows banners). Games it cannot draw in, such as Vulkan and DirectX 12 games, keep showing banners the same way as before.

The controller firmware is unchanged from the previous release; there is no need to update it.

20261010_2120 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-10-10

Game profiles now set the controller the same way every time a game starts, plus fixes from a full review of the firmware and the Utility.

Game profiles: every profile now says whether the game runs in XInput or Keyboard (Disconnect) mode, and starting the game applies every setting of that mode, so a game always behaves the same whatever a previous game, a mode button or a shortcut left behind. Keyboard-mode profiles now also apply their 8-to-6 key map, turbo key repeat, custom keys and exit combo. Empty cells in the Game profiles table show the value that will apply (from the "No known game detected" row) in italics. A profile without a turbo setting leaves turbo to the cabinet's turbo button, starting off in each game. Changes to the running game's profile apply straight away, and the profile is put back when the controller restarts or reconnects. Games without a profile keep the mode the players picked.

Firmware fixes: in Keyboard mode, START+BACK types Esc again, as the 2025 firmware did. With the 8-to-6 switch on, holding LB or LT no longer changes the button layout. Analog Slow and pinball nudges no longer misbehave when a direction is held for a long time. Turning 8-to-6 off now always turns it fully off. An update that was started but not finished (for example because the Utility was closed) no longer leaves the controls unresponsive until the controller is unplugged: it returns to normal after about a minute. The 4000H2 ST-Link image now starts correctly. Settings are now stored in a part of the chip every F103VC is guaranteed to have; existing settings move across automatically on the first start.

Utility fixes: a controller still on 2025 firmware is recognised and offered the one-click ST-Link update, and a firmware file for a different board is refused; the overlay no longer appears when overlays are switched off; swapping controllers no longer saves one controller's settings onto another; starting the Utility no longer takes the controller out of Keyboard mode; theme files can only add images to the icon folder; update progress and errors are clearer.

Update the controller firmware to get the firmware fixes (F103VB boards: use the one-click ST-Link update).

20261008_0454 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-10-07

Firmware fix for Windows PCs: after the PC was shut down and switched back on (or woke from sleep), only one player's controls worked until the board was switched to Disconnect mode and back. All players now keep working through shutdown, restart and sleep. The board's XInput controllers now share one Windows driver, the way the 2025 firmware did.

Also fixed: in rare cases the controls or the Utility connection could stop responding after Windows reset the USB connection, until the board was reconnected.

Update the controller firmware to get these fixes (F103VB boards: use the one-click ST-Link update). The first time a board with this firmware is connected, Windows sets it up again, which takes a few seconds; player order and settings are unchanged.

20260928_0408 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-27

A reorganised Utility, per-player button mapping, and per-game Analog Slow and nudge speed.

The Utility now opens on Game profiles, and the sidebar is grouped: Play (Game profiles, Test & Log), Controller - settings saved on the controller (Modes, Default XInput Mapping, Default Keyboard Mapping, Pinball Inputs, and the new Wiring & Hardware page) - and This PC - settings saved in the Utility (Overlays, App Settings, Update / About, Help). Wiring & Hardware gathers what you set once when building a cabinet: mode-pin wiring, spare pins (one table now, for both button and key output), kiosk, input debounce and USB identity. Analog Slow is now part of Modes, all update settings live on Update / About, and backup/restore is on App Settings. Controller pages say so when no controller is connected instead of showing blank tables.

With this firmware, Default XInput Mapping can remap one cabinet position instead of all players, and any button can be set to "Nothing". "Buttons that trigger modes and pinball inputs" has a new "Stop game output" tick box, so a button borrowed for a pinball flipper or a mode no longer also sends its own button to games. Game profiles gain per-game "Analog slow" and "Nudge speed" columns, "Save as reusable profile..." on a row's right-click menu, and a tag showing which saved profile a row uses.

Also: Pinball Inputs explains what feeds each input (and how to add inputs on boards without pinball pins); Restore Keyboard Map Defaults restores the real factory keys; the overlay reset no longer wipes your hotkeys, themes or update settings; edits to debounce, wiring, kiosk, shortcuts and special inputs are no longer lost when you leave a page; Analog Slow no longer shows empty boxes; one tray icon instead of two; Help rewritten; language switching no longer leaves the previous language on screen. Firmware also restores the default debounce and Esc exit on boards whose settings date from very old firmware.

Note: this firmware stores settings in a new format. If you ever go back to an older firmware, the controller runs on factory settings until you update again; your settings are kept and return with the update.

20260922_2306 earlytesting Linux / Batocera 2026-09-22

Game profiles now work on Batocera, RetroPie and Lakka. PactoLink recognises the game you start from EmulationStation (the emulator, the RetroArch core and the ROM) and switches the encoder to that game's profile, then puts it back when you quit. Profiles use the same names as the Windows Utility, so a profile set up on a PC matches the same game on your cabinet. Nothing changes on your encoder until you create a profile: while no profiled game runs, the encoder stays exactly as its switches set it. Set profiles up from the Profiles page of the PactoLink web page on your cabinet's address.

20260922_1835 earlytesting Linux / Batocera 2026-09-22

Firmware updates now work from Batocera, RetroPie and Lakka too. Open the PactoLink web page on the cabinet's address and use the Firmware section exactly as in the Windows Utility: it checks for new firmware, downloads and verifies it, and updates the encoder over its normal USB cable. Encoders with the new USB bootloader can also be repaired from here if their firmware is missing or will not start, and no ST-Link is needed. Firmware actions from another device on your network ask for the PIN shown on the cabinet.

20260920_0439 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-19

New: USB-only firmware updates and recovery (no ST-Link needed). Boards programmed with the new factory image carry a small USB bootloader; the Utility updates them over the normal cable and can repair a board whose firmware is missing or not starting: open the Firmware page, arm "catch", and power-cycle the board. Existing boards keep working exactly as before and are migrated by one ST-Link flash of the new full image. Also: the boot countdown shown on the display now matches when the controllers actually appear.

20260919_2116 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-19

Adjustable input debounce, and a smaller firmware image.

Adjustable debounce (Utility, Mode input wiring page) - Three settings in steps of 0.1 ms: Joystick directions (1.5 ms), Action buttons including pinball inputs (1.5 ms), and Start/Back with the mode inputs and exit button (10 ms). - The shipped values suit every microswitch we have tested. Lower them only if a control feels sluggish; raise one only if a specific worn switch registers twice. - The board samples its inputs about every 0.4 ms, so differences smaller than that are not measurable. - Applies live and is saved with the rest of the board settings. Needs this firmware; older firmware keeps its fixed values and the controls stay hidden.

Firmware - The debounce windows for Start/Back and the mode inputs go from 15 ms to 10 ms; joystick and buttons from 2 ms to 1.5 ms. - The firmware image is 1.8 KB smaller than 20260919_1945 even with the new feature, from removing the C library's text formatting code.

20260919_1954 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-19

Pacto 3000T firmware now works. The 3-player board was missing its entire 3-player code path: it appeared on the PC as three Xbox 360 controllers but never actually sent any input, and none of its mode pins or 8-second shortcuts did anything. This release adds the full 3-player mode engine and report path, so a 3000T now behaves like the rest of the range: player-order modes (2 Player = 1,3,2 cabinet order by default, 3 Player = 1,2,3), the three stick output modes (Fast Analog, Slow Analog, D-Pad), single-player Twinstick (cabinet sticks 1 and 2 both drive the left stick so you can use left+right or middle+right, stick 3 drives the right stick), Turbo, 8-to-6 conversion, Interlock and Disconnect mode. A new 3000T user manual is included. Every board variant was re-verified on real hardware for this build: 3000T 145/145, 4000T 170/170, 2000T 123/123, 2000H 126/126, 4000H 172/172, 1000T 97/97. No behaviour changes on any board other than the 3000T.

20260919_1945 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-19

Pre-ship firmware review: 50 fixes across every board, verified on hardware.

Controls and latency - Fixed a 13-second control blackout at every power-on on 4-player boards fitted with a DongleMaster (the loop dropped to 8 updates per second while the boot countdown re-drew the OLED). - Button remaps that swap or rotate buttons no longer lose inputs. - Idle boards no longer stream a report every millisecond; reports go out only when something changes, and analog ramps still update at the full 1 kHz. - Pinball nudge: no longer zeroes your own stick, is instant in Analog-Fast, and wins over a held stick.

Modes and shortcuts - On 3- and 4-player boards the 8-to-6 shortcut (P2 Start + P2 Right) no longer also switches 2-Player mode, and the Disconnect combo (P1 Back + P2 Back) no longer also changes the stick mode. Each single-button 8-second hold now needs to be the only Start, Back or direction held. - Disconnect mode can be left by holding Player 1 Back or Player 2 Back alone for 8 seconds, as the manuals' FAQ describes. - Holding the Disconnect combo while powering on now really boots into Disconnect mode. - Disconnect set to "Toggle" in the Utility (and kiosk "locked + switch") can now leave keyboard mode, cancel an exit countdown, and follow the Utility's Keyboard-off command. - 1000T: the SHIFT input works (every SHIFT shortcut was dead), the D-Pad shortcut leaves Right-Stick mode, and the 8-to-6 right-hand variant can be chosen with LB. - 4-player turbo shortcuts respect kiosk and the Utility's per-shortcut disable/hold; the turbo set window ends when Player 4 Start is released. - Keyboard mode: Player 3's buttons 3 and 4 now type the MAME keys (Enter/O on X/Y, F16/F17 on LB/RB); saved configs are repaired automatically. Keyboard turbo restarts its cycle on every press so short taps always type.

4000H2 - DIP1 (kiosk lock-down), DIP2 (D-Pad default) and DIP4/DIP5 (USB power force-on) now work and are shown in the Utility; inputs on ports F/G read correctly.

Reliability - OLED bus stalls can no longer block the controls; the update link no longer drops command replies when the Utility was closed for a while; bootloader firmware updates are bounded and never jump into a half-written image; several USB control-transfer edge cases fixed.

Manuals - Turbo enables on the A button only (hold the shortcut and press the buttons you want on turbo). Turbo switch wiring corrected (ground TURBO, switch on !TURB). 4000T 3-position stick switch tip corrected. 4000H has no 8-to-6 pins (shortcut only). New 3000T manual.

20260919_1601 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-19

Firmware: 4-player boards (4000T, 4000H, 4000H2, SNAP4) no longer power the DongleMaster while in XInput mode. Yesterday's build powered it 3 s after the arcade controls connected so dongle gamepads could ride as extra DInput players; on Windows a wireless XInput gamepad on that dongle can take player 1 away from the arcade controls whenever it wakes, so the original rule is back: in XInput mode the four arcade players own all four XInput slots and the DongleMaster stays off. Keyboard/disconnect mode still powers it after 12.5 s, and 1/2/3-player boards still power it 3 s after their controls connect.

20260919_0543 earlytesting App 2026-09-18

Test & Log: an XInput pad (8BitDo, Xbox) no longer shows a second DInput card - its XInput-driver HID interface is read with the right button order (Back/Start/LS/RS were being taken for triggers), so it matches its XInput player slot.

20260919_0506 earlytesting App 2026-09-18

Control Test (Test & Log page): the rumble test now stops the motors on every slot when the pulse ends and whenever pads re-enumerate, so a controller can no longer be left rumbling.

20260919_0447 earlytesting App 2026-09-18

Control Test (Test & Log page): controllers on wireless receivers stay listed by Windows after the pad is switched off; their card now dims after 45 s without any input and says so.

20260919_0432 earlytesting App 2026-09-18

The on-screen overlays are more opaque (corner badge 80 percent, centre banner 95 percent; installs still on the old defaults are lifted automatically - your own values are kept). Control Test: an encoder interface can no longer show up twice (as an XInput player and again as a slot-less pad); slot-less interfaces are identified by what they actually send and labelled with their board interface number.

20260919_0416 earlytesting App 2026-09-18

Control Test (Test & Log page): with many controllers paired, the PactoTech encoder interfaces are always shown first, an encoder that got no XInput player slot at all is flagged (red panel, banner, spoken warning), and spoken button names use the card number you see.

20260919_0357 earlytesting App 2026-09-18

Control Test (Test & Log page): gamepads that also carry a mouse interface (8BitDo 2.4G / Bluetooth receivers) no longer show up as pointing devices until that interface actually moves.

20260919_0348 earlytesting App 2026-09-18

Control Test (Test & Log page): the Dino battle has sound effects for every action, the shooting gallery puts up one CPU dino per shooter (up to 12 mice / light guns), and the tester header buttons no longer overlap.

20260919_0341 earlytesting App 2026-09-18

Control Test (Test & Log page): the Dino battle is now off until you press the Dino battle button in the tester header or hold A + B for 3 s on any controller (the Settings switch is gone). Play alone for 20 s and the PC takes another dino and comes after you, gently; shoot with a mouse or light gun while no controller is in use and four CPU dinos run around for you to hit.

20260919_0314 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-18

Firmware: 4-player boards now power the DongleMaster 3 seconds after their own controls connect (like the 2-player boards), so gamepads on the DongleMaster are available to games that take more than 4 players. The board also reports the state of every mode-input pin to the PC. Utility: the Control Test on the Test & Log page lists those pin states beside the arcade panel, and gains the Dino battle - a tiny dinosaur per controller that appears when you touch it and fights the others with every button (mice, trackballs and light guns shoot with their crosshair); switch it off under Settings > Control Test extras.

20260919_0240 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-18

Firmware: the board now reports the state of every mode-input pin (2P/4P/twin stick, d-pad/analog fast/slow, turbo, 8to6, interlock, keyboard/DIS, right stick, pinball, shift) to the PC. Utility: the Test & Log page's Control Test lists those pin states to the right of the arcade panel (needs this firmware), and the agent API exposes them as status.pins.

20260918_0547 earlytesting App 2026-09-17

Control Test (Test & Log page): the mouse speed graphs move the way they did before (one point per frame) - the previous build cleared them instantly - with thinner lines and smaller labels.

20260918_0522 earlytesting App 2026-09-17

Automatic updates: a new "When automatic updates are installed" choice under the two auto-update switches (both still off by default). "At start-up only" installs in the first minutes after the Utility starts and never while a game is running; "Live" installs as soon as a 15-minute check finds a newer app or controller firmware, even mid-game - for testing new builds on a cabinet.

20260918_0504 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-17

Firmware fix: in the analog stick modes, holding DOWN and LEFT together produced no output (every other direction and d-pad mode were fine). Cause: the full-scale DOWN+LEFT corner is the one place both axes reach -32768, and the stick merge arithmetic overflowed there. Fixed on all boards; verified on the bench. Utility: controller cards show every detail, a poll rate for pads that only report on change, and a stronger rumble test with a visible glow.

20260918_0451 earlytesting App 2026-09-17

Control Test (Test & Log page): controller cards show all of their details (the line wraps instead of being cut off), pads that only report on change (Xbox pads) get a "Hz while active" poll rate, and the rumble test is a full-strength 800 ms pulse with a visible glow on the card.

20260918_0442 earlytesting App 2026-09-17

Control Test (Test & Log page): mouse / trackball speed graphs now plot every single report instead of one point per screen frame, and get more room; each device's full name and details sit with its graph; a Pacto encoder that is not in player position 1 is flagged even when the position ahead of it is empty.

20260918_0417 earlytesting App 2026-09-17

Control Test (Test & Log page): empty XInput slots are hidden instead of dimmed; the arcade panel keeps working when another controller took an earlier player position - it turns red, explains that the controls are not properly enumerated (use a DongleMaster, or cycle keyboard mode and back) and says so out loud; each mouse, trackball or light gun now shows its full name and details with its speed graph.

20260918_0350 earlytesting App 2026-09-17

Control Test (Test & Log page): in keyboard mode the arcade panel now tells the plain Enter key and the keypad Enter key apart, so a button mapped to Enter no longer also lights the button mapped to keypad Enter (the keyboard strip already showed them correctly).

20260918_0311 earlytesting App 2026-09-17

Control Test arcade panel: BACK is now drawn on the left and START on the right, matching the physical panel.

20260918_0305 earlytesting App 2026-09-17

Test page voice: announcements are now short - "P 1 A", "P 2 L T" - instead of "Player 1 A", and the Control Test no longer speaks a start-up phrase. Control Test: shows a note when the connected board's firmware does not report everything the tester can display (mode, button remap tables, keyboard-mode key map) and points you to the firmware update in the Configurator; the full-screen tester only holds the screen for the first few seconds after a front end launches it, so Alt+Tab works normally afterwards.

20260916_0548 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-15

New DirectInput identity: the USB identity setting now has a third choice, DirectInput (HID gamepads), next to XInput (PC) and Console. It behaves exactly like XInput mode - same player order, modes, turbo, 8-to-6, keyboard mode and mode switching - but the board shows up as ordinary HID game controllers instead of Xbox controllers, for games and emulators that do not use XInput or when you have more than four players. Apply it from the Utility as you would the console identity (the board reboots; it comes back in about 15 seconds). Turbo now verified working inside keyboard mode (keys pulse at the turbo rate). Firmware fixes: on 2-player boards the "turbo off" shortcut (P1 START + DOWN) turned turbo ON; and two unset turbo flags could randomly drop the board out of keyboard mode. Control Test: the full-screen tester now stays in front of CoinOps / RetroFE (it used to run hidden behind the wheel) and writes PactoTech-ControlTest.log next to the exe for support.

20260916_0457 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-15

Utility: Control Test built in, and 8-to-6 now works inside keyboard mode. The Test & Log page has a new Control test section: a live view of every controller, mouse, trackball, light gun, keyboard and MIDI device on the PC, the XInput / DirectInput / SDL player order, polling rates, mouse speed graphs with 8-bit clipping detection, and this board's arcade panel in its current mode (2 player, 4 player, twin stick, 8-to-6, keyboard mode with every button's key). It flags a controller that takes a player position ahead of the Pacto board, with the advice to manage it through the DongleMaster. Open full screen or in a window from the same page; hold ESC or START+BACK to leave. Firmware: the 8-to-6 button shortcut no longer drops the board out of keyboard mode, so 8-to-6 switches the keyboard map while you stay in keyboard mode (the pin and the Utility already did).

20260916_0446 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-15

Utility: Control Test built in, and 8-to-6 now works inside keyboard mode. The Test & Log page has a new Control test section: a live view of every controller, mouse, trackball, light gun, keyboard and MIDI device on the PC, the XInput / DirectInput / SDL player order, polling rates, mouse speed graphs with 8-bit clipping detection, and this board's arcade panel in its current mode (2 player, 4 player, twin stick, 8-to-6, keyboard mode with every button's key). It flags a controller that takes a player position ahead of the Pacto board, with the advice to manage it through the DongleMaster. Open full screen or in a window from the same page; hold ESC or START+BACK to leave. Firmware: the 8-to-6 button shortcut no longer drops the board out of keyboard mode, so 8-to-6 switches the keyboard map while you stay in keyboard mode (the pin and the Utility already did).

20260915_0624 earlytesting App 2026-09-15

Utility: keyboard-map read-out for the new PactoTech Control Test app. The local agent API gains a read-only GET /agent/kbmap route (both profiles, 4 headers x 18 inputs) so the full-screen Control Test app can draw the arcade panel with each button's key while the Utility is running. No behaviour change otherwise.

20260915_0242 earlytesting App 2026-09-14

Utility: AI agent access. An AI assistant (Claude, ChatGPT, a local agent) can now configure the Utility and the controller for you. App Options has a new "AI agent access" section with a "Copy bootstrap prompt" button: paste that prompt into your assistant and ask for what you want, for example "swap A and B for player 2 in Street Fighter" or "make the corner badge bigger". The assistant reads and changes settings, game profiles, live modes, button remaps, keyboard maps and board parameters through a local, token-protected connection on this PC only; nothing is reachable from the network or from web pages, and the switch in App Options turns it off. The settings and game-profile files in the config folder can also be edited by hand or by a script and are picked up live, with every setting written out so nothing has to be guessed.

20260915_0150 earlytesting App 2026-09-14

Utility: optional automatic updates now install as soon as a release appears. With "Update the app automatically" or "Update controller firmware automatically" switched on (App Options; both are off by default so installs stay exactly as they are unless you choose otherwise), the Utility checks its update channel every 15 minutes instead of every 6 hours and installs right away. Updates are never applied while a game is running or while you have unsaved edits; firmware installs over USB only, and boards that need an ST-Link are never flashed on their own.

20260914_0036 earlytesting App 2026-09-13

Utility: the board's connection countdowns ("Connecting gamepads", "Connecting arcade controls") now show on the PC screen too, the same as on the SpecVision display. The corner badge stays up for the whole countdown and ticks down in place, then clears once the controls have reconnected.

Utility: new App Options setting "Keep the corner badge clear of". Steam and Windows show their "controller connected" pop-ups in the bottom-right corner by default, right when the Pacto board reconnects, so a corner badge placed there now moves to the top-right instead. Pick another corner if your Steam notifications are set elsewhere, or "Nothing" to keep the badge exactly where you set it.

20260913_2301 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-13

Utility: the mode overlay (and the sidebar chips and tray) now show Turbo on/off and 8-to-6 on/off when they are changed at the board with a switch pin or an 8-second button shortcut. The board always announced these changes, but the Utility could discard the announcement when it arrived while another request to the board was in progress, which was most of the time because the display mirror polls continuously. Announcements are now kept and delivered.

Firmware (all boards): one announcement per mode change. A turbo toggle used to send two identical announcements back to back, which made the overlay replace its "TURBO ON" banner with the player-layout name a moment later.

20260912_1803 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-09-12

Utility: fixes arcade front ends (RetroFE / CoinOPS and other SDL-based launchers) losing controls while the Utility runs in the background. The Utility's windows could briefly take the screen focus when the app started or when a second copy launched, and SDL front ends stop reading the controller the moment they lose focus. The mode overlay window is now created so it can never take focus, the settings window no longer flashes at start-up, and a second background launch is ignored. Overlays over full-screen games are unchanged.

Firmware (all boards): 8-to-6 button conversion now matches the manual. Previously every build applied the alternate "shift-right" table whenever 8-to-6 was enabled (X became LT, Y became X, and so on). The default is now the documented shift-left conversion: RB acts as LB, LB as LT, RT as RB and LT as RT, with X/Y/A/B unchanged. The shift-right variant (hold LB or LT while enabling) still works as before.

20260713_0751 earlytesting App 2026-07-13

You can now run OLDER versions from the Updates page - for the app as well as the firmware. In the app section, 'Run a different app version' lists every published version with its notes; picking one installs it and turns automatic app updates off so it stays put (turn them back on in App Options whenever you want the newest again).

Because some features need the app and controller firmware to move together, every version now shows the firmware it shipped with - and if your controller is on a different one, the app points out which firmware to flash to match. Firmware versions likewise show the app of their day.

Older app installers are archived from this release onward, so the list will grow over time.

20260713_0252 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-13

Game profiles are now a spreadsheet. Every game is a row you can edit in place - player mode, stick, custom controls, turbo with per-button checkboxes and speeds shown in Hz, and a new Exit Function per game. Sort or filter by any column, select ranges of cells and copy/paste values across them like Excel, right-click to copy a whole profile onto other games, and hide columns you don't use. Profiles are grouped into three tables: what to do when NO known game is running, games you added yourself, and games added from the game database - with a Default/Modified marker and play counts.

The game database is rebuilt from MAME's own data: 19,000+ arcade games with player counts, simultaneous-play, buttons, and control types (trackball, spinner, paddle, lightgun and more) shown right in the table.

New Exit Function: choose what the cabinet's exit button (or holding Start+Back with interlock) does - the classic gamepad Start+Back, or typing a key combo like ESC or Alt+F4, even while the sticks are working as gamepads. There's a global setting on the Modes page, and any game can override it. This needs the controller firmware in this release.

Full Custom controls: map any button on the panel to any output - another player's button, or a keyboard key - per game.

New Game & program history section: see what ran and when, with play counts, and add a profile straight from a history entry (the app recommends whether to profile the game, the emulator, or the RetroArch core). History can be turned off; browser tab titles are only recorded if you opt in (off by default for privacy).

Excel export/import: edit your profiles as a spreadsheet with dropdowns and a full Help sheet explaining every option, then import it back - great for bulk editing or AI-assisted editing. Profiles are also now included in "Back up settings to file".

The two detection toggles are now one clear switch: "Apply game profiles automatically". When nothing recognized is running, the controller now rests in your "No known game detected" profile (2 Player, Analog Fast, turbo off by default).

Controller firmware in this release adds the Exit Function and Full Custom output engines (config version 12 - your saved settings migrate automatically).

20260712_2012 earlytesting App 2026-07-12

Fixed automatic updates sometimes not running until you visited the Updates page. If the update check failed because the app started before your network was connected (common when the app launches at login), it silently waited hours before trying again. It now retries every few minutes until a check succeeds, and rechecks the moment your connection comes back.

20260712_1941 earlytesting App 2026-07-12

Game profiles got a big usability pass. Every game is now a single line showing its key settings at a glance - click to expand the full editor. Platforms (MAME, RetroArch, Steam, front ends...) are collapsible sections, and each platform now has its own default profile that covers every game on it, separate from per-game settings.

RetroArch games can now take profiles per CORE - set a default for your SNES core once and every SNES game uses it.

You can also profile any program directly: 'Choose a program...' lets you pick an .exe and attach a profile to it.

The sidebar now shows the game you're playing (or the last one detected), whether a profile was applied automatically, and a one-click button to edit that game's profile. Games are tracked by their process now, so clicking into the Utility no longer counts as 'leaving' the game.

Automatic MAME and front-end profiles now always state turbo explicitly (on with tuned timing, or off) instead of leaving it unset.

20260712_1105 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-12

Game profiles got a lot smarter:

Your Steam library is found automatically — every installed Steam game appears in the games list, ready to profile, and is recognized the moment it runs.

Auto-profile MAME games: one click profiles thousands of arcade games with the right player mode for YOUR board — it knows the player count of ~15,000 games (including the separate 2-player and 4-player versions of games like TMNT, Sunset Riders and The Simpsons), the twin-stick games (Robotron, Smash T.V., ...), and which classic shoot-em-ups should have turbo (Raiden at full speed, the Toaplan classics at 15 Hz, Battle Garegga slowed on purpose — and games where holding the button matters, like DoDonPachi's laser, are left alone).

Turbo per game: every profile can now force turbo on any combination of buttons with adjustable speed shown in Hz, or force it off. Profiles also get an 8to6 on/off option.

Front ends: RetroFE, HyperSpin, LaunchBox/Big Box, CoinOPS, Playnite, EmulationStation and friends — plus Steam and Steam Big Picture — are recognized, and one button sets them all to 2 Player, Analog Fast, Turbo off, 8to6 off so menus always behave.

This update includes new firmware (per-game turbo support).

20260712_1033 earlytesting App 2026-07-12

The connection box (bottom left) now shows your controller's chip variant next to the firmware — for example "FW 20260711 2317 · VB" — so it's always clear which chip a board has. Works on all variants; controllers on older firmware simply don't show it.

20260711_2317 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-11

Game profiles now map buttons per player: advanced profiles have P1–P4 tabs, so each player's controls can be remapped independently for a specific game. Applied while the game runs, back to normal when it exits.

The games catalog grew: TeknoParrot with 72 PC-arcade titles (Initial D, Wangan Midnight Maximum Tune, Mario Kart GP DX, House of the Dead and more), plus yuzu and Ryujinx with 35 popular Switch titles.

The DISC. KEYBD chip in the sidebar is now clickable — one click switches the controller into keyboard mode (your USB gamepads take over; the controller briefly reconnects, that's normal), another click brings it back.

This update includes new firmware for the per-player mapping and the clickable keyboard switch.

20260711_2122 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-11

NEW: Game profiles. The Utility can now detect which game is running — emulators and their ROMs (MAME, RetroArch, Dolphin, PCSX2 and ~30 more), plus regular Windows games — and apply a controller profile automatically: switch player layout, stick output, or even flip to keyboard mode so a gamepad-only game uses your DongleMaster gamepads. Set a default per emulator, override individual games, remap every button per game with advanced profiles, and save named profiles to reuse anywhere. A built-in catalog of 570 popular games gets you started; everything you actually run is learned automatically. When a game closes, your controller goes back exactly how it was.

Fixed: on controllers with older firmware, the app could flash "update available" in a loop and make the Update button hard to click. The app now handles older firmware gracefully.

Firmware: each board type now identifies its USB layout distinctly, fixing a Windows quirk where owning two different Pacto board types could stop the app from connecting to one of them (expect a brief one-time driver refresh the first time you connect after updating). Keyboard mode can now also be switched from software — used by Game profiles and available to launcher scripts.

20260711_1907 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-11

The Utility's SpecVision view now works on every controller — even without a SpecVision attached, the sidebar shows exactly what one would display (labeled "SpecVision preview").

Fixed the Test page gamepad diagrams drawing dark with the direction indicators invisible.

Test page cleanup: the mode and special input pins are now large readable tiles that light up as you press, and the duplicate lists (per-player pin rows, mode status) are gone — the controller diagrams and sidebar already show those.

Fixed a false "this board's firmware doesn't report pin states" message that could appear on up-to-date controllers.

20260711_1239 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-11

Keyboard/Disconnect mode: returning to gamepad mode now shows the countdown on the SpecVision display and the on-screen overlay, matching what you already saw when switching into keyboard mode.

The Utility now shows your SpecVision display live in the sidebar, so you can see exactly what the controller shows.

Updates page: your controller's installed firmware and the newest available now sit right above each other with the differences highlighted, and updating is a single click. Advanced options let you install any earlier version — we keep every release — and manually pick a board or chip for recovery.

New in App Options: keep the app and your controller firmware up to date automatically — both off by default.

Also includes the earlier fix for a startup freeze on 1- and 2-player boards used with a SpecVision display and a DongleMaster, and a tidied keyboard-mode overlay.

20260710_0537 earlytesting App 2026-07-09

Simpler Update page. Instead of separate boxes for the in-app update and the ST-Link tool (with a note that could contradict them), the controller now shows one plain line telling you exactly what to do: it's up to date, there's an update you install over the USB cable, or this controller updates with an ST-Link - with only the button or steps that apply. Boards with the 128 KB F103VB chip (some 2000H and 4000H) are told plainly that they update with the ST-Link flasher, which is normal for that chip - not old firmware and not a one-time step - and the page names your exact chip (for example "4000H (F103VB)").

Also included: in-game overlays that show over fullscreen games. Games in exclusive fullscreen (MAME's default on Windows) used to hide the mode-change banners because Windows won't let any other window draw over them; the Utility now draws the banner inside the game's own picture, the same way the Steam and Discord overlays do. It's on by default (App Options -> "Draw banners over fullscreen games"). Because it works by drawing into the game, some antivirus tools may flag the Utility - if that happens you can turn it off there and use the per-emulator options (a small MAME plugin, or RetroArch's Network Commands) instead.

20260710_0500 earlytesting App 2026-07-09

In-game overlays now show over fullscreen games. Games running in exclusive fullscreen (MAME's default on Windows) used to hide the mode-change banners entirely, because Windows won't let any other window draw over an exclusive-fullscreen game. The Utility now draws the banner inside the game's own picture, so it shows over any fullscreen game - the same technique the Steam and Discord overlays use. It's on by default (App Options -> "Draw banners over fullscreen games"). Note: because this works by drawing into the game, some antivirus tools may flag the Utility; if that happens you can turn it off there and use the per-emulator options instead. For MAME you can install a small plugin (App Options -> Install MAME plugin) and RetroArch shows the banners once its Network Commands are enabled - neither of those needs the in-game overlay.

Clearer firmware-update messages: boards with the 128 KB F103VB chip (some 2000H and 4000H boards) now say plainly that they update with the ST-Link flasher - this is normal for that chip, not a one-time step and not old firmware - and the Update page names your exact chip (for example "4000H (F103VB)"). A misleading "already updates from the app" note has been removed for boards that actually need the ST-Link.

20260710_0415 earlytesting Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-10

Fixes a startup freeze on 1- and 2-player boards used with a SpecVision display and a DongleMaster: the controller could lock up shortly after plugging in and stay unresponsive until power-cycled.

Also completes the Disconnect/Keyboard mode fixes from the previous release for 1-player boards - entering keyboard mode with the D-PAD mode switch turned on now sticks on every board.

20260710_0250 earlytesting Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-10

Firmware fix for all boards: Disconnect/Keyboard mode could immediately jump back to gamepad mode on cabinets with the D-PAD mode switch turned on - entering keyboard mode now sticks, whether started from the Utility app or the DIS input.

Cabinets wired with a maintained Disconnect switch also work correctly again: hold the switch closed at power-on to start in keyboard mode, and flip it off to return to gamepad mode.

20260709_0621 earlytesting Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-09

Critical firmware fixes - update recommended for ALL boards:

Cabinets with a SpecVision attached could hang at power-on and look stuck in a boot loop: after display init the I2C bus ran far above its 25 kHz design speed, and a bus error could freeze the controller entirely. The bus now stays at its intended speed, display interrupts can no longer starve the system, and the controller recovers automatically within 100 ms if the display link ever locks up.

The DISS (Disconnect/Keyboard) input on all boards except the 4000H2 was electrically floating - boards with nothing wired to DISS could randomly enter keyboard mode or reboot repeatedly. The input now has its pull-up enabled, matching every other mode input.

Boards with the F103VB chip (some 2000H/4000H) update with the in-app ST-Link flasher; everything else updates in-app over USB.

20260709_0440 earlytesting App 2026-07-08

Fixes the sidebar "update available" notice staying visible after everything is already up to date (the sections were right - the notice just could not hide).

20260709_0209 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-08

Easier updates: the Update page now checks for updates automatically when opened, highlights the next step, and greys out anything that's already done; an "update available" notice appears in the sidebar next to the connection status. Fixed: the ST-Link section no longer stays highlighted after a successful flash.

Firmware fix: a "CONNECTING ARCADE CONTROLS - 12s" message could stay frozen on the overlay and SpecVision after power-on (on boards with a DongleMaster attached). This firmware fixes it, and the app's overlay now also clears a stuck message on older firmware by itself.

New - Windows / Linux mode (USB identity, Modes page): boards in Batocera, RetroPie or Lakka cabinets can be set to Linux mode, where the controls run on the system's own built-in Xbox 360 driver - real native gamepads, no extra software in the input path. The board keeps full configurator support via Keyboard mode on Windows, and the Help section covers everything including a one-line Linux installer.

Clearer settings: pinball inputs and mode-wiring options now always stay visible with per-board notes (greyed items explain which boards have them and how to add the feature with remapping), and the turbo switch wiring is spelled out (permanent ground on TURBO, switch on !TURB).

20260708_0500 earlytesting Linux / Batocera 2026-07-07

First PactoLink release for Linux emulation systems: Batocera, RetroPie, Lakka and desktop Linux.

Mode changes pop right on the cabinet screen (PC Batocera) or as RetroArch messages in-game, and the full Pacto configurator is served to any browser on your network at http://<cabinet-ip>:46810. Keyboard/Disconnect mode works out of the box for MAME-style play; native gamepad (XInput) support on Linux arrives with the upcoming "Linux mode" firmware update: switch the board's USB identity to Linux mode and Linux's own built-in Xbox-pad driver runs the controls directly.

One-line install on any of them: curl -L https://raw.githubusercontent.com/leecyrille/PactoTech_Public_Releases/main/install.sh | sh (RetroPie/desktop Linux: | sudo sh) - the script detects your system and installs the right signed package; the releases README has step-by-step instructions including how to open a terminal or SSH in. Batocera can also install with no terminal at all: drop the zip contents on the cabinet's share and launch "Install PactoLink" from the Ports menu. Raspberry Pi (aarch64) builds are included but still experimental. See the Help section in the app or web configurator for step-by-step guides.

20260708_0313 earlytesting App 2026-07-07

The Help section now covers Batocera, RetroPie and desktop Linux: what works today (keyboard mode out of the box, remote configuration from any browser or phone on your network), the one-time setup lines, and honest notes on gamepad support and on-screen overlays. Remote configuration stays open on your local network by default - viewing is always open, and an optional PIN can protect changes if you want it.

20260708_0234 earlytesting App 2026-07-07

Fixes in-app firmware updates failing with 'firmware package is inconsistent' - the app mis-read the update package header. Update the app first, then firmware updates install normally. (Found by installing firmware 20260708_0046 on the bench through the exact customer path.)

20260708_0046 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-07

The Test screen now shows the raw electrical state of every input pin - including the mode pins - straight off the connectors, perfect for checking cabinet wiring (needs this firmware). The keyboard test shows just the keys being sent right now instead of a wall of every mapped key, and both keyboard keys and mode-pin presses are announced by voice.

The Help section now says which boards each feature applies to (a 2000T has no 4-player mode, twin stick isn't available on the 3000T, the 4000H uses button combos instead of TURBO/8TO6 pins, and so on).

When your board already updates from the app, the ST-Link flashing tool is dimmed with a note pointing at the normal update button - it stays available for recovery.

20260708_0018 earlytesting App 2026-07-07

Corrects the ST-Link flashing guidance: when the chip can't be reached, the Utility now points at the usual causes - SWD wiring and making sure the board runs from its own power (an ST-Link's 3V3 pin can't power a whole board) - while it keeps retrying through a power-cycle.

20260707_2348 earlytesting App 2026-07-07

Adds a searchable Help section covering every feature: player modes and twin stick, Disconnect/Keyboard mode and the DongleMaster, remapping, turbo, shortcuts, overlays and themes, kiosk mode, LaunchBox scripts, firmware updates, ST-Link flashing, update channels, backup, and troubleshooting. Type a word into the search box and matching topics open with the hits highlighted.

20260707_1343 earlytesting App 2026-07-07

Fixes ST-Link detection failing with 'the debug probe could not be created' - the Utility was holding its own connection to the ST-Link open while trying to connect a second time. Also renames the About page to Update / About.

20260707_0554 earlytesting App 2026-07-07

Fixes from early testing feedback.

Flashing with ST-Link is more resilient: if the chip can't be reached, the Utility keeps retrying with clear guidance - check the wiring, make sure the board has its own power, and power-cycle it. Detect once, then flash - no extra tools needed.

Test screen voice announcements now stop when the Utility window is in the background or closed to the tray.

Update checks and downloads no longer hang - a failed firmware download says so clearly and can be retried. The What's-new list now explains when releases exist on a different update channel than yours, and older installs are moved off the retired 'production' channel name automatically.

20260707_0419 earlytesting App 2026-07-06

The Utility can now flash boards with an ST-Link, right from the app.

If your board is on firmware from before in-app updates existed (or has the F103VB chip), you no longer need any external flashing tools: connect an ST-Link V2 to the board's SWD header, pick your board model in the Utility's firmware section, and press Flash. The app reads the chip itself, downloads the matching signed image, and refuses anything that doesn't fit your exact hardware.

Also fixes update-signature verification for in-app firmware updates.

20260707_0353 earlytesting App + Firmware 1000T-F103VC · 2000H-F103VB · 2000H-F103VC · 2000T-F103VC · 3000T-F103VC · 4000H-F103VB · 4000H-F103VC · 4000H2-F103ZE · 4000T-F103VC · SNAP2-F103VC · SNAP4-F103VC 2026-07-06

First Early Testing release of the new Pacto Tech software platform.

The Pacto Tech Utility for Windows: live controller status and input testing, full remapping for XInput and keyboard outputs, mode controls with editable shortcuts, customizable on-screen overlays and themes, kiosk/lockdown modes for cabinets, ready-made scripts for LaunchBox and other frontends, and automatic app updates on your chosen channel.

New firmware for every current board (1000T, 2000T, 2000H, 3000T, 4000T, 4000H, 4000H2, SNAP2, SNAP4 - including the F103VB chip variants of the 2000H/4000H and the F103ZE-based 4000H2) introduces in-app firmware updates: flash your board once with the matching ST-Link image from this release, and every update after that installs from inside the Utility with a couple of clicks. Updates are checked against your exact board model AND its chip, an interrupted update can't brick the board, and a file for the wrong board simply won't apply. Boards with the smaller F103VB chip keep updating via ST-Link (no room for the update system on that chip) - the Utility tells you when a new version is out for them.

Also improved: much cleaner switching between arcade (XInput) and gamepad/keyboard (DISS.) modes, per-input mode settings, twin-stick 1P/2P modes, and turbo refinements.